Heat-affected zone

The effects of welding on the material surrounding the weld can be detrimental —depending on the materials used and the heat input of the welding process used, the HAZ can be of varying size and strength. The thermal diffusivity of the base material plays a large role — if the diffusivity is high, the material cooling rate is high and the HAZ is relatively small. Conversely, a low diffusivity leads to slower cooling and a larger HAZ. The amount of heat injected by the welding process plays an important role as well, as processes like oxyacetylene welding have an unconcentrated heat input and increase the size of the HAZ. Processes like laser beam welding give a highly concentrated, limited amount of heat, resulting in a small HAZ. Arc welding falls between these two extremes, with the individual processes varying somewhat in heat input. To calculate the heat input for arc welding procedures, the following formula can be used:

Where Q = heat input (kJ/mm), V = voltage (V), / = current (A), and S = welding speed (mm/min). The efficiency is dependent on the welding process used, with shielded metal arc welding having a value of 0.75, gas metal arc welding and submerged arc welding, 0.9, and gas tungsten arc welding, 0.8.

Distortion and cracking

Welding methods that involve the melting of metal at the site of the joint necessarily are prone to shrinkage as the heated metal cools. Shrinkage, in turn, can introduce residual stresses and both longitudinal and rotational distortion. Distortion can pose a major problem, since the final product is not the desired shape. To alleviate rotational distortion, the work pieces can be offset, so that the welding results in a .correctly shaped piece.

Заведующий кафедрой

общеобразовательных дисциплин

____________ В.П. Павлов

Уфимский государственный Кафедра общеобразовательных

авиационный технический дисциплин

университет

ЭКЗАМЕНАЦИОННЫЙ БИЛЕТ № 20

Факультет: АТС (СП) Вопрос: 1

Electrogas welding

Electrogas welding (EGW) is a continuous vertical position arc welding process developed in 1961, in which an arc is struck between a consumable electrode and the workpiece. A shielding gas is sometimes used, but pressure is not applied. A major difference between EGW and its cousin electroslag welding is that the arc in EGW is not extinguished, instead remaining struck throughout the welding process. It is used to make square-groove welds for butt and t-joints, especially in the shipbuilding industry and in the construction of storage tanks.

Operation

In EGW, the heat of the welding arc causes the electrode and workpieces to melt and flow into the cavity between the parts being welded. This molten metal solidifies from the bottom up, joining the parts being welded together. The weld area is protected from atmospheric contamination by a separate shielding gas, or by the gas produced by the disintegration of a flux-cored electrode wire. The electrode is guided into the weld area by either a consumable electrode guide tube, like the one used in electroslag welding, or a moving head. When the consumable guide tube is used, the weld pool is composed of molten metal coming from the parts being welded, the electrode, and the guide tube. The moving head variation uses an assembly of an electrode guide tube which travels upwards as the weld is laid, keeping it from melting.

Electrogas welding can be applied to most steels, including low and medium carbon steels, low alloy high strength steels, and some stainless steels. Quenched and tempered steels may also be welded by the process, provided that the proper amount of heat is applied. Welds must be vertical, varying to either side by a maximum of 15 degrees. In general, the workpiece must be at least 10 mm (0.4 in) thick, while the maximum thickness for one electrode is approximately 20 mm (0.8 in). Additional electrodes make it possible to weld thicker workpieces. The height of the weld is limited only by the mechanism used to lift the welding head — in general; it ranges from 100 mm (4 in) to 20 m (50 ft). Like other arc welding processes, EGW requires that the operator wear a welding helmet and proper attire to prevent exposure to molten metal and the bright welding arc. Compared to other processes, a large amount of molten metal is present during welding, and this poses an additional safety and fire hazard.