- •Features
- •1. Pin Configurations
- •2. Overview
- •2.1 Block Diagram
- •2.2 Pin Descriptions
- •2.2.3 Port B (PB7:PB0) – XTAL1/XTAL2/TOSC1/TOSC2
- •2.2.4 Port C (PC5:PC0)
- •2.2.5 PC6/RESET
- •2.2.6 Port D (PD7:PD0)
- •2.2.7 RESET
- •2.2.9 AREF
- •2.2.10 ADC7:6 (TQFP and QFN/MLF Package Only)
- •3. Resources
- •4. Data Retention
- •5. About Code Examples
- •6. AVR CPU Core
- •6.1 Overview
- •6.2 Arithmetic Logic Unit – ALU
- •6.3 Status Register
- •6.3.1 SREG – The AVR Status Register
- •6.4 General Purpose Register File
- •6.5 Stack Pointer
- •6.5.1 SPH and SPL – Stack Pointer High and Low Register
- •6.6 Instruction Execution Timing
- •6.7 Reset and Interrupt Handling
- •6.7.1 Interrupt Response Time
- •7. AVR Memories
- •7.1 Overview
- •7.3 SRAM Data Memory
- •7.3.1 Data Memory Access Times
- •7.4 EEPROM Data Memory
- •7.4.1 EEPROM Read/Write Access
- •7.5 I/O Memory
- •7.6 Register Description
- •7.6.1 EEARH and EEARL – The EEPROM Address Register
- •7.6.2 EEDR – The EEPROM Data Register
- •7.6.3 EECR – The EEPROM Control Register
- •7.6.5 Preventing EEPROM Corruption
- •8. System Clock and Clock Options
- •8.1 Clock Systems and their Distribution
- •8.2 Clock Sources
- •8.3 Crystal Oscillator
- •8.5 External RC Oscillator
- •8.6 Calibrated Internal RC Oscillator
- •8.7 External Clock
- •8.8 Timer/Counter Oscillator
- •8.9 Register Description
- •8.9.1 OSCCAL – Oscillator Calibration Register
- •9. Power Management and Sleep Modes
- •9.1 Sleep Modes
- •9.2 Idle Mode
- •9.3 ADC Noise Reduction Mode
- •9.6 Standby Mode
- •9.7 Minimizing Power Consumption
- •9.7.2 Analog Comparator
- •9.7.4 Internal Voltage Reference
- •9.7.5 Watchdog Timer
- •9.7.6 Port Pins
- •9.8 Register Description
- •9.8.1 MCUCR – MCU Control Register
- •10. System Control and Reset
- •10.1 Resetting the AVR
- •10.2 Reset Sources
- •10.2.2 External Reset
- •10.2.4 Watchdog Reset
- •10.3 Internal Voltage Reference
- •10.4 Watchdog Timer
- •10.5 Timed Sequences for Changing the Configuration of the Watchdog Timer
- •10.5.1 Safety Level 1 (WDTON Fuse Unprogrammed)
- •10.5.2 Safety Level 2 (WDTON Fuse Programmed)
- •10.6 Register Description
- •10.6.1 MCUCSR – MCU Control and Status Register
- •10.6.2 WDTCR – Watchdog Timer Control Register
- •11. Interrupts
- •11.1 Interrupt Vectors in ATmega8A
- •11.1.1 Moving Interrupts Between Application and Boot Space
- •11.2 Register Description
- •11.2.1 GICR – General Interrupt Control Register
- •12. I/O Ports
- •12.1 Overview
- •12.2 Ports as General Digital I/O
- •12.2.1 Configuring the Pin
- •12.2.2 Reading the Pin Value
- •12.2.3 Digital Input Enable and Sleep Modes
- •12.2.4 Unconnected pins
- •12.3 Alternate Port Functions
- •12.3.1 SFIOR – Special Function IO Register
- •12.3.2 Alternate Functions of Port B
- •12.3.3 Alternate Functions of Port C
- •12.3.4 Alternate Functions of Port D
- •12.4 Register Description
- •12.4.1 PORTB – The Port B Data Register
- •12.4.2 DDRB – The Port B Data Direction Register
- •12.4.3 PINB – The Port B Input Pins Address
- •12.4.4 PORTC – The Port C Data Register
- •12.4.5 DDRC – The Port C Data Direction Register
- •12.4.6 PINC – The Port C Input Pins Address
- •12.4.7 PORTD – The Port D Data Register
- •12.4.8 DDRD – The Port D Data Direction Register
- •12.4.9 PIND – The Port D Input Pins Address
- •13. External Interrupts
- •13.1 Register Description
- •13.1.1 MCUCR – MCU Control Register
- •13.1.2 GICR – General Interrupt Control Register
- •13.1.3 GIFR – General Interrupt Flag Register
- •14. 8-bit Timer/Counter0
- •14.1 Features
- •14.2 Overview
- •14.2.1 Registers
- •14.2.2 Definitions
- •14.3 Timer/Counter Clock Sources
- •14.4 Counter Unit
- •14.5 Operation
- •14.6 Timer/Counter Timing Diagrams
- •14.7 Register Description
- •14.7.1 TCCR0 – Timer/Counter Control Register
- •14.7.2 TCNT0 – Timer/Counter Register
- •14.7.3 TIMSK – Timer/Counter Interrupt Mask Register
- •14.7.4 TIFR – Timer/Counter Interrupt Flag Register
- •15. Timer/Counter0 and Timer/Counter1 Prescalers
- •15.1 Overview
- •15.2 Internal Clock Source
- •15.3 Prescaler Reset
- •15.4 External Clock Source
- •15.5 Register Description
- •15.5.1 SFIOR – Special Function IO Register
- •16. 16-bit Timer/Counter1
- •16.1 Features
- •16.2 Overview
- •16.2.1 Registers
- •16.2.2 Definitions
- •16.2.3 Compatibility
- •16.3.1 Reusing the Temporary High Byte Register
- •16.4 Timer/Counter Clock Sources
- •16.5 Counter Unit
- •16.6 Input Capture Unit
- •16.6.1 Input Capture Pin Source
- •16.6.2 Noise Canceler
- •16.6.3 Using the Input Capture Unit
- •16.7 Output Compare Units
- •16.7.1 Force Output Compare
- •16.7.2 Compare Match Blocking by TCNT1 Write
- •16.7.3 Using the Output Compare Unit
- •16.8 Compare Match Output Unit
- •16.8.1 Compare Output Mode and Waveform Generation
- •16.9 Modes of Operation
- •16.9.1 Normal Mode
- •16.9.2 Clear Timer on Compare Match (CTC) Mode
- •16.9.3 Fast PWM Mode
- •16.9.4 Phase Correct PWM Mode
- •16.9.5 Phase and Frequency Correct PWM Mode
- •16.10 Timer/Counter Timing Diagrams
- •16.11 Register Description
- •16.11.1 TCCR1A – Timer/Counter 1 Control Register A
- •16.11.2 TCCR1B – Timer/Counter 1 Control Register B
- •16.11.3 TCNT1H and TCNT1L – Timer/Counter 1
- •16.11.4 OCR1AH and OCR1AL– Output Compare Register 1 A
- •16.11.5 OCR1BH and OCR1BL – Output Compare Register 1 B
- •16.11.6 ICR1H and ICR1L – Input Capture Register 1
- •17. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- •17.1 Features
- •17.2 Overview
- •17.2.1 Registers
- •17.2.2 Definitions
- •17.3 Timer/Counter Clock Sources
- •17.4 Counter Unit
- •17.5 Output Compare Unit
- •17.5.1 Force Output Compare
- •17.5.2 Compare Match Blocking by TCNT2 Write
- •17.5.3 Using the Output Compare Unit
- •17.6 Compare Match Output Unit
- •17.6.1 Compare Output Mode and Waveform Generation
- •17.7 Modes of Operation
- •17.7.1 Normal Mode
- •17.7.2 Clear Timer on Compare Match (CTC) Mode
- •17.7.3 Fast PWM Mode
- •17.7.4 Phase Correct PWM Mode
- •17.8 Timer/Counter Timing Diagrams
- •17.9 Asynchronous Operation of the Timer/Counter
- •17.9.1 Asynchronous Operation of Timer/Counter2
- •17.10 Timer/Counter Prescaler
- •17.11 Register Description
- •17.11.1 TCCR2 – Timer/Counter Control Register
- •17.11.2 TCNT2 – Timer/Counter Register
- •17.11.3 OCR2 – Output Compare Register
- •17.11.4 ASSR – Asynchronous Status Register
- •17.11.5 TIMSK – Timer/Counter Interrupt Mask Register
- •17.11.6 TIFR – Timer/Counter Interrupt Flag Register
- •17.11.7 SFIOR – Special Function IO Register
- •18. Serial Peripheral Interface – SPI
- •18.1 Features
- •18.2 Overview
- •18.3 SS Pin Functionality
- •18.3.1 Slave Mode
- •18.3.2 Master Mode
- •18.4 Data Modes
- •18.5 Register Description
- •18.5.1 SPCR – SPI Control Register
- •18.5.2 SPSR – SPI Status Register
- •18.5.3 SPDR – SPI Data Register
- •19. USART
- •19.1 Features
- •19.2 Overview
- •19.2.1 AVR USART vs. AVR UART – Compatibility
- •19.3 Clock Generation
- •19.3.1 Internal Clock Generation – The Baud Rate Generator
- •19.3.2 Double Speed Operation (U2X)
- •19.3.3 External Clock
- •19.3.4 Synchronous Clock Operation
- •19.4 Frame Formats
- •19.4.1 Parity Bit Calculation
- •19.5 USART Initialization
- •19.6 Data Transmission – The USART Transmitter
- •19.6.1 Sending Frames with 5 to 8 Data Bits
- •19.6.2 Sending Frames with 9 Data Bits
- •19.6.3 Transmitter Flags and Interrupts
- •19.6.4 Parity Generator
- •19.6.5 Disabling the Transmitter
- •19.6.6 Data Reception – The USART Receiver
- •Receiving Frames with 5 to 8 Data Bits
- •19.6.7 Receiving Frames with 9 Data Bits
- •19.6.8 Receive Compete Flag and Interrupt
- •19.6.9 Receiver Error Flags
- •19.6.10 Parity Checker
- •19.6.11 Disabling the Receiver
- •19.7 Asynchronous Data Reception
- •19.7.1 Asynchronous Clock Recovery
- •19.7.2 Asynchronous Data Recovery
- •19.7.3 Asynchronous Operational Range
- •19.8.1 Using MPCM
- •19.9 Accessing UBRRH/UCSRC Registers
- •19.9.1 Write Access
- •19.9.2 Read Access
- •19.10 Register Description
- •19.10.1 UDR– USART I/O Data Register
- •19.10.2 UCSRA – USART Control and Status Register A
- •19.10.3 UCSRB – USART Control and Status Register B
- •19.10.4 UCSRC – USART Control and Status Register C
- •19.10.5 UBRRL and UBRRH – USART Baud Rate Registers
- •19.11 Examples of Baud Rate Setting
- •20. Two-wire Serial Interface
- •20.1 Features
- •20.2 Overview
- •20.2.1 SCL and SDA Pins
- •20.2.2 Bit Rate Generator Unit
- •20.2.3 Bus Interface Unit
- •20.2.4 Address Match Unit
- •20.2.5 Control Unit
- •20.3.1 TWI Terminology
- •20.3.2 Electrical Interconnection
- •20.4 Data Transfer and Frame Format
- •20.4.1 Transferring Bits
- •20.4.2 START and STOP Conditions
- •20.4.3 Address Packet Format
- •20.4.4 Data Packet Format
- •20.4.5 Combining Address and Data Packets into a Transmission
- •20.6 Using the TWI
- •20.6.1 Transmission Modes
- •20.6.2 Master Transmitter Mode
- •20.6.3 Master Receiver Mode
- •20.6.4 Slave Receiver Mode
- •20.6.5 Slave Transmitter Mode
- •20.6.6 Miscellaneous States
- •20.6.7 Combining Several TWI Modes
- •20.8 Register Description
- •20.8.1 TWBR – TWI Bit Rate Register
- •20.8.2 TWCR – TWI Control Register
- •20.8.3 TWI Status Register – TWSR
- •20.8.4 TWDR – TWI Data Register
- •20.8.5 TWAR – TWI (Slave) Address Register
- •21. Analog Comparator
- •21.1 Overview
- •21.2 Analog Comparator Multiplexed Input
- •21.3 Register Description
- •21.3.1 SFIOR – Special Function IO Register
- •21.3.2 ACSR – Analog Comparator Control and Status Register
- •22. Analog-to-Digital Converter
- •22.1 Features
- •22.2 Overview
- •22.3 Starting a Conversion
- •22.4 Prescaling and Conversion Timing
- •22.5 Changing Channel or Reference Selection
- •22.5.1 ADC Input Channels
- •22.5.2 ADC Voltage Reference
- •22.6 ADC Noise Canceler
- •22.6.1 Analog Input Circuitry
- •22.6.2 Analog Noise Canceling Techniques
- •22.6.3 ADC Accuracy Definitions
- •22.7 ADC Conversion Result
- •22.8 Register Description
- •22.8.1 ADMUX – ADC Multiplexer Selection Register – ADMUX
- •22.8.2 ADCSRA – ADC Control and Status Register A
- •22.8.3 ADCL and ADCH – The ADC Data Register
- •23. Boot Loader Support – Read-While-Write Self-Programming
- •23.1 Features
- •23.2 Overview
- •23.3 Application and Boot Loader Flash Sections
- •23.3.1 Application Section
- •23.3.2 BLS – Boot Loader Section
- •23.5 Boot Loader Lock Bits
- •23.6 Entering the Boot Loader Program
- •23.8.1 Performing Page Erase by SPM
- •23.8.2 Filling the Temporary Buffer (Page Loading)
- •23.8.3 Performing a Page Write
- •23.8.4 Using the SPM Interrupt
- •23.8.5 Consideration While Updating BLS
- •23.8.7 Setting the Boot Loader Lock Bits by SPM
- •23.8.8 EEPROM Write Prevents Writing to SPMCR
- •23.8.9 Reading the Fuse and Lock Bits from Software
- •23.8.10 Preventing Flash Corruption
- •23.8.11 Programming Time for Flash when using SPM
- •23.8.12 Simple Assembly Code Example for a Boot Loader
- •23.8.13 Boot Loader Parameters
- •23.9 Register Description
- •23.9.1 Store Program Memory Control Register – SPMCR
- •24. Memory Programming
- •24.1 Program And Data Memory Lock Bits
- •24.2 Fuse Bits
- •24.2.1 Latching of Fuses
- •24.3 Signature Bytes
- •24.4 Calibration Byte
- •24.5 Page Size
- •24.6 Parallel Programming Parameters, Pin Mapping, and Commands
- •24.6.1 Signal Names
- •24.7 Parallel Programming
- •24.7.1 Enter Programming Mode
- •24.7.2 Considerations for Efficient Programming
- •24.7.3 Chip Erase
- •24.7.4 Programming the Flash
- •24.7.5 Programming the EEPROM
- •24.7.6 Reading the Flash
- •24.7.7 Reading the EEPROM
- •24.7.8 Programming the Fuse Low Bits
- •24.7.9 Programming the Fuse High Bits
- •24.7.10 Programming the Lock Bits
- •24.7.11 Reading the Fuse and Lock Bits
- •24.7.12 Reading the Signature Bytes
- •24.7.13 Reading the Calibration Byte
- •24.7.14 Parallel Programming Characteristics
- •24.8 Serial Downloading
- •24.9 Serial Programming Pin Mapping
- •24.9.1 Serial Programming Algorithm
- •24.9.2 Data Polling Flash
- •24.9.3 Data Polling EEPROM
- •24.9.4 SPI Serial Programming Characteristics
- •25. Electrical Characteristics
- •25.1 Absolute Maximum Ratings*
- •25.2 DC Characteristics
- •25.3 Speed Grades
- •25.4 Clock Characteristics
- •25.4.1 External Clock Drive Waveforms
- •25.4.2 External Clock Drive
- •25.5 System and Reset Characteristics
- •25.7 SPI Timing Characteristics
- •25.8 ADC Characteristics
- •26. Typical Characteristics
- •26.1 Active Supply Current
- •26.2 Idle Supply Current
- •26.5 Standby Supply Current
- •26.7 Pin Driver Strength
- •26.8 Pin Thresholds and Hysteresis
- •26.9 Bod Thresholds and Analog Comparator Offset
- •26.10 Internal Oscillator Speed
- •26.11 Current Consumption of Peripheral Units
- •26.12 Current Consumption in Reset and Reset Pulsewidth
- •27. Register Summary
- •28. Instruction Set Summary
- •29. Ordering Information
- •30. Packaging Information
- •31. Errata
- •31.1 ATmega8A, rev. L
- •32. Datasheet Revision History
- •Table of Contents
ATmega8A
6.7Reset and Interrupt Handling
The AVR provides several different interrupt sources. These interrupts and the separate Reset Vector each have a separate Program Vector in the Program memory space. All interrupts are assigned individual enable bits which must be written logic one together with the Global Interrupt Enable bit in the Status Register in order to enable the interrupt. Depending on the Program Counter value, interrupts may be automatically disabled when Boot Lock Bits BLB02 or BLB12 are programmed. This feature improves software security. See the section “Memory Programming” on page 226 for details.
The lowest addresses in the Program memory space are by default defined as the Reset and Interrupt Vectors. The complete list of Vectors is shown in “Interrupts” on page 45. The list also determines the priority levels of the different interrupts. The lower the address the higher is the priority level. RESET has the highest priority, and next is INT0 – the External Interrupt Request 0. The Interrupt Vectors can be moved to the start of the boot Flash section by setting the Interrupt Vector Select (IVSEL) bit in the General Interrupt Control Register (GICR). Refer to “Interrupts” on page 45 for more information. The Reset Vector can also be moved to the start of the boot Flash section by programming the BOOTRST Fuse, see “Boot Loader Support – Read- While-Write Self-Programming” on page 212.
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared and all interrupts are disabled. The user software can write logic one to the I-bit to enable nested interrupts. All enabled interrupts can then interrupt the current interrupt routine. The I-bit is automatically set when a Return from Interrupt instruction – RETI – is executed.
There are basically two types of interrupts. The first type is triggered by an event that sets the Interrupt Flag. For these interrupts, the Program Counter is vectored to the actual Interrupt Vector in order to execute the interrupt handling routine, and hardware clears the corresponding Interrupt Flag. Interrupt Flags can also be cleared by writing a logic one to the flag bit position(s) to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is cleared, the Interrupt Flag will be set and remembered until the interrupt is enabled, or the flag is cleared by software. Similarly, if one or more interrupt conditions occur while the global interrupt enable bit is cleared, the corresponding Interrupt Flag(s) will be set and remembered until the global interrupt enable bit is set, and will then be executed by order of priority.
The second type of interrupts will trigger as long as the interrupt condition is present. These interrupts do not necessarily have Interrupt Flags. If the interrupt condition disappears before the interrupt is enabled, the interrupt will not be triggered.
When the AVR exits from an interrupt, it will always return to the main program and execute one more instruction before any pending interrupt is served.
Note that the Status Register is not automatically stored when entering an interrupt routine, nor restored when returning from an interrupt routine. This must be handled by software.
When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled. No interrupt will be executed after the CLI instruction, even if it occurs simultaneously with the
13
8159C–AVR–07/09
ATmega8A
CLI instruction. The following example shows how this can be used to avoid interrupts during the timed EEPROM write sequence.
Assembly Code Example
in r16, SREG ; store SREG value
cli ; disable interrupts during timed sequence sbi EECR, EEMWE ; start EEPROM write
sbi EECR, EEWE
out SREG, r16 ; restore SREG value (I-bit)
C Code Example
char cSREG;
cSREG = SREG; /* store SREG value */
/* disable interrupts during timed sequence */
_CLI();
EECR |= (1<<EEMWE); /* start EEPROM write */
EECR |= (1<<EEWE);
SREG = cSREG; /* restore SREG value (I-bit) */
When using the SEI instruction to enable interrupts, the instruction following SEI will be executed before any pending interrupts, as shown in the following example.
Assembly Code Example
sei ; set global interrupt enable
sleep; enter sleep, waiting for interrupt
;note: will enter sleep before any pending
;interrupt(s)
C Code Example
_SEI(); /* set global interrupt enable */
_SLEEP(); /* enter sleep, waiting for interrupt */
/* note: will enter sleep before any pending interrupt(s) */
6.7.1Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles minimum. After four clock cycles, the Program Vector address for the actual interrupt handling routine is executed. During this 4-clock cycle period, the Program Counter is pushed onto the Stack. The Vector is normally a jump to the interrupt routine, and this jump takes three clock cycles. If an interrupt occurs during execution of a multi-cycle instruction, this instruction is completed before the interrupt is served. If an interrupt occurs when the MCU is in sleep mode, the interrupt execution response time is increased by four clock cycles. This increase comes in addition to the start-up time from the selected sleep mode.
A return from an interrupt handling routine takes four clock cycles. During these four clock cycles, the Program Counter (2 bytes) is popped back from the Stack, the Stack Pointer is incremented by 2, and the I-bit in SREG is set.
14
8159C–AVR–07/09