ELECTRICAL SYSTEM 16-47

Lighting System

This motorcycle adopt the daylight system and have a headlight relay in the relay box. The headlight does not go on when the ignition switch and the engine stop switch are first turned on. The headlight comes on after the starter button is released and stays on until the ignition switch is turned off. The headlight will go out momentarily whenever the starter button is pressed and come back on when the button is released.

Headlight Beam Horizontal Adjustment

•Refer to the Headlight Aiming Inspection in the Periodic Maintenance chapter.

Headlight Beam Vertical Adjustment

•Refer to the Headlight Aiming Inspection in the Periodic Maintenance chapter.

Headlight Bulb Replacement

•Disconnect the headlight connector [A].

•Turn the headlight bulb [A] counterclockwise and pull out the bulb from the headlight.

CAUTION

When handling the quartz-halogen bulb, never touch the glass portion with bare hands. Always use a clean cloth. Oil contamination from hands or dirty rags can reduce bulb life or cause the bulb to explode.

NOTE

○Clean off any contamination that inadvertently gets on the bulb with alcohol or soap and water solution.

•Replace the headlight bulb.

•Fit the projections [A] of the bulb in the hollows [B] of the headlight.

16-48 ELECTRICAL SYSTEM

Lighting System

•Turn the headlight bulb [A] clockwise.

•Connect the headlight connector.

•After installation, adjust the headlight aim (see Headlight Aiming Inspection in the Periodic Maintenance chapter).

○Other Bulb: Repeat the above steps.

City Light Bulb Replacement

•Remove the upper inner fairings (see Upper Inner Fairing Removal in the Frame chapter).

•Open the clamp [A].

•Pull out the socket [B] together with the bulb.

•Pull the bulb [A] out of the socket [B].

CAUTION

Do not turn the bulb. Pull the bulb out to prevent damage to the bulb. Do not use bulb rated for greater wattage than the specified value.

•Replace the bulb with a new one.

•Insert the socket [A] to the headlight.

○Fit the socket into the grooves [B] of the headlight. ○Other Bulb: Repeat the above steps.

Headlight Removal/Installation

•Remove:

Upper Fairing Assembly (see Upper Fairing Assembly Removal in the Frame chapter)

Bolts [A] and Clamps Headlight [B]

•Installation is the reverse of removal.

ELECTRICAL SYSTEM 16-49

Lighting System

Tail/Brake Light (LED) Removal/Installation

•Remove:

Rear Seat Cover (see Seat Cover Removal in the Frame chapter)

Bolts [A]

Tail/Brake Light (LED) [B]

•Installation is the reverse of removal, note the following. ○Fit the projections [A] of the rear seat cover into the slots

[B] of the tail/brake light (LED).

License Plate Light Bulb Replacement

•Remove: Screws [A]

License Plate Light Cover [B]

•Pull the bulb [A] out of the socket [B].

CAUTION

Do not turn the bulb. Pull the bulb out to prevent damage to the bulb. Do not use bulb rated for greater wattage than the specified value.

•Replace the bulb with a new one.

•Tighten:

Torque - License Plate Light Cover Screws: 1.0 N·m (0.10 kgf·m, 8.9 in·lb)

16-50 ELECTRICAL SYSTEM

Lighting System

Headlight/Tail Light Circuit

1.	Ignition Switch	13.	Main Fuse 30 A
2.	Regulator/Rectifier	14.	Relay Box
3.	Alternator	15.	Headlight Circuit Relay
4.	License Plate Light 12 V 5 W	16.	Dimmer Switch
5.	Tail/Brake Light (LED) 13.5 V 0.5/4.1 W	17.	Passing Button
6.	Joint Connector C	18.	Joint Connector A
7.	Taillight Fuse 10 A	19.	Left City Light 12 V 5 W
8.	Headlight Fuse 15 A	20.	Headlight (HI) 12 V 65 W
9. Fuse Box		21.	Headlight (LO) 12 V 55 W
10.	Battery 12 V 8 Ah	22.	Right City Light 12 V 5 W
11.	Frame Ground	23.	Joint Connector B
12.	Starter Relay	24.	High Beam Indicator Light (LED)