- •1. Pin Configurations
- •1.1 Disclaimer
- •2. Overview
- •2.1 Block Diagram
- •2.2 Pin Descriptions
- •2.2.3 Port B (PB3...PB0)
- •2.2.4 RESET
- •2.2.5 Port A (PA7...PA0)
- •3. Resources
- •4. About Code Examples
- •5. CPU Core
- •5.1 Overview
- •5.2 Architectural Overview
- •5.4 Status Register
- •5.5 General Purpose Register File
- •5.6 Stack Pointer
- •5.7 Instruction Execution Timing
- •5.8 Reset and Interrupt Handling
- •5.8.1 Interrupt Response Time
- •6. Memories
- •6.2 SRAM Data Memory
- •6.2.1 Data Memory Access Times
- •6.3 EEPROM Data Memory
- •6.3.1 EEPROM Read/Write Access
- •6.3.2 Atomic Byte Programming
- •6.3.3 Split Byte Programming
- •6.3.4 Erase
- •6.3.5 Write
- •6.3.6 Preventing EEPROM Corruption
- •6.4 I/O Memory
- •6.4.1 General Purpose I/O Registers
- •6.5 Register Description
- •7. System Clock and Clock Options
- •7.1 Clock Systems and their Distribution
- •7.2 Clock Sources
- •7.3 Default Clock Source
- •7.4 Crystal Oscillator
- •7.6 Calibrated Internal RC Oscillator
- •7.7 External Clock
- •7.8 128 kHz Internal Oscillator
- •7.9 System Clock Prescaler
- •7.9.1 Switching Time
- •7.10 Register Description
- •8. Power Management and Sleep Modes
- •8.1 Sleep Modes
- •8.2 Idle Mode
- •8.3 ADC Noise Reduction Mode
- •8.5 Standby Mode
- •8.6 Power Reduction Register
- •8.7 Minimizing Power Consumption
- •8.7.1 Analog to Digital Converter
- •8.7.2 Analog Comparator
- •8.7.4 Internal Voltage Reference
- •8.7.5 Watchdog Timer
- •8.7.6 Port Pins
- •8.8 Register Description
- •9. System Control and Reset
- •9.0.1 Resetting the AVR
- •9.0.2 Reset Sources
- •9.0.3 Power-on Reset
- •9.0.4 External Reset
- •9.0.6 Watchdog Reset
- •9.1 Internal Voltage Reference
- •9.2 Watchdog Timer
- •9.3 Timed Sequences for Changing the Configuration of the Watchdog Timer
- •9.3.1 Safety Level 1
- •9.3.2 Safety Level 2
- •9.4 Register Description
- •10. Interrupts
- •10.1 Interrupt Vectors
- •11. External Interrupts
- •11.1 Pin Change Interrupt Timing
- •11.2 Register Description
- •12. I/O Ports
- •12.1 Overview
- •12.2 Ports as General Digital I/O
- •12.2.1 Configuring the Pin
- •12.2.2 Toggling the Pin
- •12.2.3 Switching Between Input and Output
- •12.2.4 Reading the Pin Value
- •12.2.5 Digital Input Enable and Sleep Modes
- •12.2.6 Unconnected Pins
- •12.3 Alternate Port Functions
- •12.3.1 Alternate Functions of Port A
- •12.3.2 Alternate Functions of Port B
- •12.4 Register Description
- •13. 8-bit Timer/Counter0 with PWM
- •13.1 Features
- •13.2 Overview
- •13.2.1 Registers
- •13.2.2 Definitions
- •13.3 Timer/Counter Clock Sources
- •13.4 Counter Unit
- •13.5 Output Compare Unit
- •13.5.1 Force Output Compare
- •13.5.2 Compare Match Blocking by TCNT0 Write
- •13.5.3 Using the Output Compare Unit
- •13.6 Compare Match Output Unit
- •13.6.1 Compare Output Mode and Waveform Generation
- •13.7 Modes of Operation
- •13.7.1 Normal Mode
- •13.7.2 Clear Timer on Compare Match (CTC) Mode
- •13.7.3 Fast PWM Mode
- •13.7.4 Phase Correct PWM Mode
- •13.8 Timer/Counter Timing Diagrams
- •13.9 Register Description
- •14. 16-bit Timer/Counter1
- •14.1 Features
- •14.2 Overview
- •14.2.1 Registers
- •14.2.2 Definitions
- •14.2.3 Compatibility
- •14.3.1 Reusing the Temporary High Byte Register
- •14.4 Timer/Counter Clock Sources
- •14.5 Counter Unit
- •14.6 Input Capture Unit
- •14.6.1 Input Capture Trigger Source
- •14.6.2 Noise Canceler
- •14.6.3 Using the Input Capture Unit
- •14.7 Output Compare Units
- •14.7.1 Force Output Compare
- •14.7.2 Compare Match Blocking by TCNT1 Write
- •14.7.3 Using the Output Compare Unit
- •14.8 Compare Match Output Unit
- •14.8.1 Compare Output Mode and Waveform Generation
- •14.9 Modes of Operation
- •14.9.1 Normal Mode
- •14.9.2 Clear Timer on Compare Match (CTC) Mode
- •14.9.3 Fast PWM Mode
- •14.9.4 Phase Correct PWM Mode
- •14.9.5 Phase and Frequency Correct PWM Mode
- •14.10 Timer/Counter Timing Diagrams
- •14.11 Register Description
- •15. Timer/Counter Prescaler
- •15.0.1 Prescaler Reset
- •15.0.2 External Clock Source
- •15.1 Register Description
- •16.1 Features
- •16.2 Overview
- •16.3 Functional Descriptions
- •16.3.2 SPI Master Operation Example
- •16.3.3 SPI Slave Operation Example
- •16.3.5 Start Condition Detector
- •16.3.6 Clock speed considerations
- •16.4 Alternative USI Usage
- •16.4.4 Edge Triggered External Interrupt
- •16.4.5 Software Interrupt
- •16.5 Register Descriptions
- •17. Analog Comparator
- •17.1 Analog Comparator Multiplexed Input
- •17.2 Register Description
- •18. Analog to Digital Converter
- •18.1 Features
- •18.2 Overview
- •18.3 ADC Operation
- •18.4 Starting a Conversion
- •18.5 Prescaling and Conversion Timing
- •18.6 Changing Channel or Reference Selection
- •18.6.1 ADC Input Channels
- •18.6.2 ADC Voltage Reference
- •18.7 ADC Noise Canceler
- •18.7.1 Analog Input Circuitry
- •18.7.2 Analog Noise Canceling Techniques
- •18.7.3 ADC Accuracy Definitions
- •18.8 ADC Conversion Result
- •18.8.1 Single Ended Conversion
- •18.8.2 Unipolar Differential Conversion
- •18.8.3 Bipolar Differential Conversion
- •18.9 Temperature Measurement
- •18.10 Register Description
- •18.10.3.1 ADLAR = 0
- •18.10.3.2 ADLAR = 1
- •19. debugWIRE On-chip Debug System
- •19.1 Features
- •19.2 Overview
- •19.3 Physical Interface
- •19.4 Software Break Points
- •19.5 Limitations of debugWIRE
- •19.6 Register Description
- •20. Self-Programming the Flash
- •20.0.1 Performing Page Erase by SPM
- •20.0.2 Filling the Temporary Buffer (Page Loading)
- •20.0.3 Performing a Page Write
- •20.1.1 EEPROM Write Prevents Writing to SPMCSR
- •20.1.2 Reading the Fuse and Lock Bits from Software
- •20.1.3 Preventing Flash Corruption
- •20.1.4 Programming Time for Flash when Using SPM
- •20.2 Register Description
- •21. Memory Programming
- •21.1 Program And Data Memory Lock Bits
- •21.2 Fuse Bytes
- •21.2.1 Latching of Fuses
- •21.3 Signature Bytes
- •21.4 Calibration Byte
- •21.5 Page Size
- •21.6 Serial Downloading
- •21.6.1 Serial Programming Algorithm
- •21.6.2 Serial Programming Instruction set
- •21.7 High-voltage Serial Programming
- •21.8.2 Considerations for Efficient Programming
- •21.8.3 Chip Erase
- •21.8.4 Programming the Flash
- •21.8.5 Programming the EEPROM
- •21.8.6 Reading the Flash
- •21.8.7 Reading the EEPROM
- •21.8.8 Programming and Reading the Fuse and Lock Bits
- •21.8.9 Reading the Signature Bytes and Calibration Byte
- •22. Electrical Characteristics
- •22.1 Absolute Maximum Ratings*
- •22.2 Speed Grades
- •22.3 Clock Characterizations
- •22.3.1 Calibrated Internal RC Oscillator Accuracy
- •22.3.2 External Clock Drive Waveforms
- •22.3.3 External Clock Drive
- •22.4 System and Reset Characterizations
- •22.6 Serial Programming Characteristics
- •22.7 High-voltage Serial Programming Characteristics
- •23.1 Active Supply Current
- •23.2 Idle Supply Current
- •23.3 Supply Current of IO modules
- •23.3.0.1 Example 1
- •23.5 Standby Supply Current
- •23.7 Pin Driver Strength
- •23.8 Pin Threshold and Hysteresis
- •23.9 BOD Threshold and Analog Comparator Offset
- •23.10 Internal Oscillator Speed
- •23.11 Current Consumption of Peripheral Units
- •23.12 Current Consumption in Reset and Reset Pulsewidth
- •24. Register Summary
- •25. Instruction Set Summary
- •26. Ordering Information
- •26.1 ATtiny24
- •26.2 ATtiny44
- •26.3 ATtiny84
- •27. Packaging Information
- •28. Errata
- •28.1 ATtiny24
- •28.2 ATtiny44
- •28.3 ATtiny84
- •29. Datasheet Revision History
ATtiny24/44/84
15. Timer/Counter Prescaler
Timer/Counter 0, and 1 share the same prescaler module, but the Timer/Counters can have different prescaler settings. The description below applies to all Timer/Counters. Tn is used as a general name, n = 0, 1.
The Timer/Counter can be clocked directly by the system clock (by setting the CSn2:0 = 1). This provides the fastest operation, with a maximum Timer/Counter clock frequency equal to system clock frequency (fCLK_I/O). Alternatively, one of four taps from the prescaler can be used as a
clock source. The prescaled clock has a frequency of either fCLK_I/O/8, fCLK_I/O/64, fCLK_I/O/256, or fCLK_I/O/1024.
15.0.1Prescaler Reset
The prescaler is free running, i.e., operates independently of the Clock Select logic of the Timer/CounterCounter, and it is shared by the Timer/Counter Tn. Since the prescaler is not affected by the Timer/Counter’s clock select, the state of the prescaler will have implications for situations where a prescaled clock is used. One example of prescaling artifacts occurs when the timer is enabled and clocked by the prescaler (6 > CSn2:0 > 1). The number of system clock cycles from when the timer is enabled to the first count occurs can be from 1 to N+1 system clock cycles, where N equals the prescaler divisor (8, 64, 256, or 1024).
It is possible to use the Prescaler Reset for synchronizing the Timer/Counter to program execution.
15.0.2External Clock Source
An external clock source applied to the Tn pin can be used as Timer/Counter clock (clkTn). The Tn pin is sampled once every system clock cycle by the pin synchronization logic. The synchronized (sampled) signal is then passed through the edge detector. Figure 15-1 on page 121 shows a functional equivalent block diagram of the Tn synchronization and edge detector logic. The registers are clocked at the positive edge of the internal system clock (clkI/O). The latch is transparent in the high period of the internal system clock.
The edge detector generates one clkT0 pulse for each positive (CSn2:0 = 7) or negative (CSn2:0 = 6) edge it detects.
Figure 15-1. T0 Pin Sampling |
|
|
|
|
|||
Tn |
D |
Q |
D |
Q |
D |
Q |
Tn_sync |
|
|
|
|
|
|
|
(To Clock |
|
|
|
|
|
|
|
Select Logic) |
|
LE |
|
|
|
|
|
|
clkI/O |
|
|
|
|
|
|
|
|
|
|
Synchronization |
|
|
Edge Detector |
The synchronization and edge detector logic introduces a delay of 2.5 to 3.5 system clock cycles from an edge has been applied to the Tn pin to the counter is updated.
Enabling and disabling of the clock input must be done when Tn has been stable for at least one system clock cycle, otherwise it is a risk that a false Timer/Counter clock pulse is generated.
Each half period of the external clock applied must be longer than one system clock cycle to ensure correct sampling. The external clock must be guaranteed to have less than half the sys-
121
8006E–AVR–09/06