- •1. Pin Configurations
- •1.1 Disclaimer
- •2. Overview
- •2.1 Block Diagram
- •2.2 Pin Descriptions
- •2.2.3 Port B (PB3...PB0)
- •2.2.4 RESET
- •2.2.5 Port A (PA7...PA0)
- •3. Resources
- •4. About Code Examples
- •5. CPU Core
- •5.1 Overview
- •5.2 Architectural Overview
- •5.4 Status Register
- •5.5 General Purpose Register File
- •5.6 Stack Pointer
- •5.7 Instruction Execution Timing
- •5.8 Reset and Interrupt Handling
- •5.8.1 Interrupt Response Time
- •6. Memories
- •6.2 SRAM Data Memory
- •6.2.1 Data Memory Access Times
- •6.3 EEPROM Data Memory
- •6.3.1 EEPROM Read/Write Access
- •6.3.2 Atomic Byte Programming
- •6.3.3 Split Byte Programming
- •6.3.4 Erase
- •6.3.5 Write
- •6.3.6 Preventing EEPROM Corruption
- •6.4 I/O Memory
- •6.4.1 General Purpose I/O Registers
- •6.5 Register Description
- •7. System Clock and Clock Options
- •7.1 Clock Systems and their Distribution
- •7.2 Clock Sources
- •7.3 Default Clock Source
- •7.4 Crystal Oscillator
- •7.6 Calibrated Internal RC Oscillator
- •7.7 External Clock
- •7.8 128 kHz Internal Oscillator
- •7.9 System Clock Prescaler
- •7.9.1 Switching Time
- •7.10 Register Description
- •8. Power Management and Sleep Modes
- •8.1 Sleep Modes
- •8.2 Idle Mode
- •8.3 ADC Noise Reduction Mode
- •8.5 Standby Mode
- •8.6 Power Reduction Register
- •8.7 Minimizing Power Consumption
- •8.7.1 Analog to Digital Converter
- •8.7.2 Analog Comparator
- •8.7.4 Internal Voltage Reference
- •8.7.5 Watchdog Timer
- •8.7.6 Port Pins
- •8.8 Register Description
- •9. System Control and Reset
- •9.0.1 Resetting the AVR
- •9.0.2 Reset Sources
- •9.0.3 Power-on Reset
- •9.0.4 External Reset
- •9.0.6 Watchdog Reset
- •9.1 Internal Voltage Reference
- •9.2 Watchdog Timer
- •9.3 Timed Sequences for Changing the Configuration of the Watchdog Timer
- •9.3.1 Safety Level 1
- •9.3.2 Safety Level 2
- •9.4 Register Description
- •10. Interrupts
- •10.1 Interrupt Vectors
- •11. External Interrupts
- •11.1 Pin Change Interrupt Timing
- •11.2 Register Description
- •12. I/O Ports
- •12.1 Overview
- •12.2 Ports as General Digital I/O
- •12.2.1 Configuring the Pin
- •12.2.2 Toggling the Pin
- •12.2.3 Switching Between Input and Output
- •12.2.4 Reading the Pin Value
- •12.2.5 Digital Input Enable and Sleep Modes
- •12.2.6 Unconnected Pins
- •12.3 Alternate Port Functions
- •12.3.1 Alternate Functions of Port A
- •12.3.2 Alternate Functions of Port B
- •12.4 Register Description
- •13. 8-bit Timer/Counter0 with PWM
- •13.1 Features
- •13.2 Overview
- •13.2.1 Registers
- •13.2.2 Definitions
- •13.3 Timer/Counter Clock Sources
- •13.4 Counter Unit
- •13.5 Output Compare Unit
- •13.5.1 Force Output Compare
- •13.5.2 Compare Match Blocking by TCNT0 Write
- •13.5.3 Using the Output Compare Unit
- •13.6 Compare Match Output Unit
- •13.6.1 Compare Output Mode and Waveform Generation
- •13.7 Modes of Operation
- •13.7.1 Normal Mode
- •13.7.2 Clear Timer on Compare Match (CTC) Mode
- •13.7.3 Fast PWM Mode
- •13.7.4 Phase Correct PWM Mode
- •13.8 Timer/Counter Timing Diagrams
- •13.9 Register Description
- •14. 16-bit Timer/Counter1
- •14.1 Features
- •14.2 Overview
- •14.2.1 Registers
- •14.2.2 Definitions
- •14.2.3 Compatibility
- •14.3.1 Reusing the Temporary High Byte Register
- •14.4 Timer/Counter Clock Sources
- •14.5 Counter Unit
- •14.6 Input Capture Unit
- •14.6.1 Input Capture Trigger Source
- •14.6.2 Noise Canceler
- •14.6.3 Using the Input Capture Unit
- •14.7 Output Compare Units
- •14.7.1 Force Output Compare
- •14.7.2 Compare Match Blocking by TCNT1 Write
- •14.7.3 Using the Output Compare Unit
- •14.8 Compare Match Output Unit
- •14.8.1 Compare Output Mode and Waveform Generation
- •14.9 Modes of Operation
- •14.9.1 Normal Mode
- •14.9.2 Clear Timer on Compare Match (CTC) Mode
- •14.9.3 Fast PWM Mode
- •14.9.4 Phase Correct PWM Mode
- •14.9.5 Phase and Frequency Correct PWM Mode
- •14.10 Timer/Counter Timing Diagrams
- •14.11 Register Description
- •15. Timer/Counter Prescaler
- •15.0.1 Prescaler Reset
- •15.0.2 External Clock Source
- •15.1 Register Description
- •16.1 Features
- •16.2 Overview
- •16.3 Functional Descriptions
- •16.3.2 SPI Master Operation Example
- •16.3.3 SPI Slave Operation Example
- •16.3.5 Start Condition Detector
- •16.3.6 Clock speed considerations
- •16.4 Alternative USI Usage
- •16.4.4 Edge Triggered External Interrupt
- •16.4.5 Software Interrupt
- •16.5 Register Descriptions
- •17. Analog Comparator
- •17.1 Analog Comparator Multiplexed Input
- •17.2 Register Description
- •18. Analog to Digital Converter
- •18.1 Features
- •18.2 Overview
- •18.3 ADC Operation
- •18.4 Starting a Conversion
- •18.5 Prescaling and Conversion Timing
- •18.6 Changing Channel or Reference Selection
- •18.6.1 ADC Input Channels
- •18.6.2 ADC Voltage Reference
- •18.7 ADC Noise Canceler
- •18.7.1 Analog Input Circuitry
- •18.7.2 Analog Noise Canceling Techniques
- •18.7.3 ADC Accuracy Definitions
- •18.8 ADC Conversion Result
- •18.8.1 Single Ended Conversion
- •18.8.2 Unipolar Differential Conversion
- •18.8.3 Bipolar Differential Conversion
- •18.9 Temperature Measurement
- •18.10 Register Description
- •18.10.3.1 ADLAR = 0
- •18.10.3.2 ADLAR = 1
- •19. debugWIRE On-chip Debug System
- •19.1 Features
- •19.2 Overview
- •19.3 Physical Interface
- •19.4 Software Break Points
- •19.5 Limitations of debugWIRE
- •19.6 Register Description
- •20. Self-Programming the Flash
- •20.0.1 Performing Page Erase by SPM
- •20.0.2 Filling the Temporary Buffer (Page Loading)
- •20.0.3 Performing a Page Write
- •20.1.1 EEPROM Write Prevents Writing to SPMCSR
- •20.1.2 Reading the Fuse and Lock Bits from Software
- •20.1.3 Preventing Flash Corruption
- •20.1.4 Programming Time for Flash when Using SPM
- •20.2 Register Description
- •21. Memory Programming
- •21.1 Program And Data Memory Lock Bits
- •21.2 Fuse Bytes
- •21.2.1 Latching of Fuses
- •21.3 Signature Bytes
- •21.4 Calibration Byte
- •21.5 Page Size
- •21.6 Serial Downloading
- •21.6.1 Serial Programming Algorithm
- •21.6.2 Serial Programming Instruction set
- •21.7 High-voltage Serial Programming
- •21.8.2 Considerations for Efficient Programming
- •21.8.3 Chip Erase
- •21.8.4 Programming the Flash
- •21.8.5 Programming the EEPROM
- •21.8.6 Reading the Flash
- •21.8.7 Reading the EEPROM
- •21.8.8 Programming and Reading the Fuse and Lock Bits
- •21.8.9 Reading the Signature Bytes and Calibration Byte
- •22. Electrical Characteristics
- •22.1 Absolute Maximum Ratings*
- •22.2 Speed Grades
- •22.3 Clock Characterizations
- •22.3.1 Calibrated Internal RC Oscillator Accuracy
- •22.3.2 External Clock Drive Waveforms
- •22.3.3 External Clock Drive
- •22.4 System and Reset Characterizations
- •22.6 Serial Programming Characteristics
- •22.7 High-voltage Serial Programming Characteristics
- •23.1 Active Supply Current
- •23.2 Idle Supply Current
- •23.3 Supply Current of IO modules
- •23.3.0.1 Example 1
- •23.5 Standby Supply Current
- •23.7 Pin Driver Strength
- •23.8 Pin Threshold and Hysteresis
- •23.9 BOD Threshold and Analog Comparator Offset
- •23.10 Internal Oscillator Speed
- •23.11 Current Consumption of Peripheral Units
- •23.12 Current Consumption in Reset and Reset Pulsewidth
- •24. Register Summary
- •25. Instruction Set Summary
- •26. Ordering Information
- •26.1 ATtiny24
- •26.2 ATtiny44
- •26.3 ATtiny84
- •27. Packaging Information
- •28. Errata
- •28.1 ATtiny24
- •28.2 ATtiny44
- •28.3 ATtiny84
- •29. Datasheet Revision History
ATtiny24/44/84
18.6Changing Channel or Reference Selection
The MUX5:0 and REFS1:0 bits in the ADMUX Register are single buffered through a temporary register to which the CPU has random access. This ensures that the channels and reference selection only takes place at a safe point during the conversion. The channel and reference selection is continuously updated until a conversion is started. Once the conversion starts, the channel and reference selection is locked to ensure a sufficient sampling time for the ADC. Continuous updating resumes in the last ADC clock cycle before the conversion completes (ADIF in ADCSRA is set). Note that the conversion starts on the following rising ADC clock edge after ADSC is written. The user is thus advised not to write new channel or reference selection values to ADMUX until one ADC clock cycle after ADSC is written.
If Auto Triggering is used, the exact time of the triggering event can be indeterministic. Special care must be taken when updating the ADMUX Register, in order to control which conversion will be affected by the new settings.
If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the ADMUX Register is changed in this period, the user cannot tell if the next conversion is based on the old or the new settings. ADMUX can be safely updated in the following ways:
a.When ADATE or ADEN is cleared.
b.During conversion, minimum one ADC clock cycle after the trigger event.
c.After a conversion, before the Interrupt Flag used as trigger source is cleared.
When updating ADMUX in one of these conditions, the new settings will affect the next ADC conversion.
18.6.1ADC Input Channels
When changing channel selections, the user should observe the following guidelines to ensure that the correct channel is selected:
In Single Conversion mode, always select the channel before starting the conversion. The channel selection may be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for the conversion to complete before changing the channel selection.
In Free Running mode, always select the channel before starting the first conversion. The channel selection may be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for the first conversion to complete, and then change the channel selection. Since the next conversion has already started automatically, the next result will reflect the previous channel selection. Subsequent conversions will reflect the new channel selection.
18.6.2ADC Voltage Reference
The reference voltage for the ADC (VREF) indicates the conversion range for the ADC. Single ended channels that exceed VREF will result in codes close to 0x3FF. VREF can be selected as either VCC, or internal 1.1V reference, or external AREF pin. The first ADC conversion result after switching reference voltage source may be inaccurate, and the user is advised to discard this result.
145
8006E–AVR–09/06