- •Features
- •Pin Configuration
- •Description
- •Block Diagram
- •Pin Descriptions
- •AVCC
- •Port A (PA7..PA0)
- •Port B (PB7..PB0)
- •XTAL1
- •XTAL2
- •Resources
- •AVR CPU Core
- •Architectural Overview
- •I/O Direct
- •Data Direct
- •Data Indirect with Displacement
- •Data Indirect
- •Memories
- •SRAM Data Memory
- •EEPROM Data Memory
- •EEPROM Read/Write Access
- •I/O Memory
- •Clock Systems and their Distribution
- •Clock Sources
- •Default Clock Source
- •Crystal Oscillator
- •External RC Oscillator
- •External Clock
- •Power-on Reset
- •External Reset
- •Brown-out Detection
- •Watchdog Reset
- •Idle Mode
- •Power-down Mode
- •Standby Mode
- •Analog to Digital Converter
- •Analog Comparator
- •Brown-out Detector
- •Internal Voltage Reference
- •Watchdog Timer
- •Port Pins
- •I/O Ports
- •Introduction
- •Configuring the Pin
- •Reading the Pin Value
- •Unconnected Pins
- •Alternate Port Functions
- •Alternate Functions of Port A
- •Alternate Functions Of Port B
- •Register Description for I/O Ports
- •Interrupts
- •Interrupt Vectors
- •Interrupt Handling
- •Interrupt Response Time
- •External Interrupt
- •Pin Change Interrupt
- •Timer/Counters
- •Timer/Counter0 Prescaler
- •Timer/Counter1 Prescaler
- •8-bit Timer/Counter0
- •8-bit Timer/Counter1
- •Timer/Counter1 in PWM Mode
- •Watchdog Timer
- •Overview
- •Register Descriptions
- •Functional Descriptions
- •Three-wire Mode
- •SPI Slave Operation Example
- •Two-wire Mode
- •Start Condition Detector
- •Alternative USI Usage
- •4-bit Counter
- •12-bit Timer/Counter
- •Software Interrupt
- •Analog Comparator
- •Analog to Digital Converter
- •Features
- •Operation
- •Changing Channel or Reference Selection
- •ADC Conversion Result
- •ADLAR = 0
- •ADLAR = 1
- •Fuse Bits
- •Latching of Fuses
- •Signature Bytes
- •Calibration Byte
- •Page Size
- •Signal Names
- •Parallel Programming
- •Enter Programming Mode
- •Chip Erase
- •Programming the Flash
- •Programming the EEPROM
- •Reading the Flash
- •Reading the EEPROM
- •Programming the Lock Bits
- •Reading the Signature Bytes
- •Reading the Calibration Byte
- •Serial Downloading
- •Data Polling Flash
- •Data Polling EEPROM
- •Electrical Characteristics
- •Absolute Maximum Ratings*
- •DC Characteristics
- •External Clock Drive Waveforms
- •External Clock Drive
- •ADC Characteristics
- •Active Supply Current
- •Idle Supply Current
- •Power-down Supply Current
- •Standby Supply Current
- •Pin Pull-up
- •Internal Oscillator Speed
- •Register Summary
- •Instruction Set Summary
- •Ordering Information
- •Packaging Information
- •Errata
- •ATtiny26 Rev. B/C/D
- •Table of Contents
Timer/Counters
Timer/Counter0
Prescaler
The ATtiny26(L) provides two general purpose 8-bit Timer/Counters. The Timer/Counters have separate prescaling selection from the separate prescaler. The Timer/Counter0 clock (CK) as the clock timebase. The Timer/Counter1 has two clocking modes, a synchronous mode and an asynchronous mode. The synchronous mode uses the system clock (CK) as the clock timebase and asynchronous mode uses the fast peripheral clock (PCK) as the clock time base.
Figure 36 below shows the Timer/Counter prescaler.
Figure 36. Timer/Counter0 Prescaler
CK |
10-BIT T/C PRESCALER |
|
|
CLEAR |
|
|
|
CK/8 |
CK/64 |
CK/256 |
CK/1024 |
PSR0 |
|
|
|
T0(PB6) |
|
|
|
|
0 |
|
|
CS00
CS01
CS02
TIMER/COUNTER0 CLOCK SOURCE
The four prescaled selections are: CK/8, CK/64, CK/256, and CK/1024 where CK is the oscillator clock. CK, external source, and stop, can also be selected as clock sources.
66 ATtiny26(L)
1477J–AVR–06/07