Ä

REAR SEATS

REAR SEAT CUSHION REMOVAL

(1)Remove bolts holding cushion to floor.

(2)Disconnect center occupant seat belts from cushion.

(3)Remove cushion from vehicle.

REAR SEAT CUSHION INSTALLATION

Reverse the preceding operation.

REAR SEAT BACK REMOVAL

(1)Remove rear seat cushion assembly.

(2)Remove bolts holding seat back to rear floor kick-up.

(3)Lift seat back upward to disengage upper hooks from shelf support panel.

(4)Separate seat back from vehicle.

REAR SEAT BACK INSTALLATION

Reverse the preceding operation.

BODY MOULDINGS

STICK-ON BODY SIDE MOULDING REMOVAL AND INSTALLATION

(1)Warm the effected stick-on moulding and body metal to approximately 38°C (100°F) using a suitable heat lamp or heat gun.

(2)Pull stick-on moulding from painted surface.

(3)Remove adhesive tape residue from painted surface of vehicle.

(4)If moulding is to be reused, Remove tape residue from moulding. Clean back of moulding with Mopart, Super Kleen solvent or equivalent. Wipe moulding dry with lint free cloth. Apply new body side moulding (two sided adhesive) tape to back of moulding.

(5)Clean body surface with Super Kleen solvent or equivalent. Wipe surface dry with lint free cloth.

(6)Apply a length of masking tape on the body, parallel to the top edge of the moulding to use as a guide, if necessary.

(7)Remove protective cover from tape on back of moulding. Apply moulding to body below the masking tape guide.

(8)Remove masking tape guide and heat body and moulding, see step one. Firmly press moulding to body surface to assure adhesion.

FRONT WHEEL OPENING MOULDING REMOVAL

(1)Remove screws holding wheel opening moulding to front fender.

(2)Separate moulding from fender.

AC-BODY 23 - 49

FRONT WHEEL OPENING MOULDING INSTALLATION

(1)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(2)Install screws around wheel opening.

REAR WHEEL OPENING MOULDING REMOVAL

(1)Remove screws holding wheel opening moulding to quarter panel.

(2)Separate wheel opening moulding from quarter panel.

REAR WHEEL OPENING MOULDING INSTALLATION

(1)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(2)Install screws around wheel opening.

VINYL ROOF BONNET

REMOVAL (FIG. 27)

(1)Remove quarter panel trim covers.

(2)Remove head lining.

(3)Remove nuts holding transverse roof moulding to roof panel and separate moulding from vehicle.

(4)Remove nuts holding vinyl top bonnet to roof.

(5)Remove rear deck filler panel.

(6)Remove screws holding rear window opening lower valance to body.

(7)Disengage hook and loop fasteners holding vinyl top bonnet to quarter panel.

(8)Pull vinyl top bonnet away from top panel to separate bonnet from anti-flutter sealer holding bonnet to roof.

INSTALLATION

(1)Clean anti-flutter sealer from roof surface and inside of vinyl roof bonnet.

(2)Apply a 20 mm (0.75 in.) bead of anti-flutter sealer across the roof panel at the mid point between the front of the bonnet and rear of roof.

(3)Apply a 20 mm (0.75 in.) by 150 mm (6 in.) bead of anti-flutter sealer down each roof side panel at mid point between the door opening and rear of roof.

(4)Place the bonnet into position on the roof panel and align to proper fit.

(5)Reverse the removal operation.

REAR DECK FILLER PANEL

REMOVAL (FIG. 28)

(1)Raise truck lid to full up position.

(2)Remove screws holding rear deck filler panel to body in the front trunk opening gutter.

(3)Close trunk lid, do not latch.

(4)Lift filler panel upward and separate from ve-

hicle.